K-patents PR-23 User Manual Page 165
- Page / 213
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
11 Safe-Drive™
157
4 1 Turn the Retractor 60 degrees clockwise (i.e. to
the right) to lock the bayonet.
2 Push down the latch on the Outer casing to
secure the connecon.
3 Insert safety pin.
5 1 Close the blow-out ball valve underneath the
Isolaon valve.
2 Li up the Isolaon valve handle locking plate.
3 Open the Isolaon valve by turning the valve
handle 90 degrees counterclockwise. The valve is
open when the ball valve handle is parallel to the
Retractor and sensor.
6 Now the sensor can be inserted into the process.
Turn the hand-wheel counterclockwise unl it
stops, i.e. unl the sensor flange connects with the
Isolaon valve and only the end of the screw thread
is visible.
Warning! If you detect leaking, revert immediately
to the previous step. Do not connue installaon
unl the reason for leakage has been cleared and
fixed.
7 Fit the four M12 nuts to the bolts holding the
sensor to the Isolaon valve and screw them on
with a 19 mm or 3/4" wrench.
Important: Do not ghten the nuts too hard, set
the torque at 50 Nm (37 /lbs).
8 1 Turn the wheel 90 degrees (a quarter turn) to the
right.
2 Remove the safety pin.
3 Unlock the latch of the Outer casing.
4 Turn the casing 60 degrees counterclockwise i.e.
unl the handle is up on top.
- REFRACTOMETER 1
- INSTRUCTION MANUAL 2
- FOR INLINE REFRACTOMETER 2
- PR-23(-...-AX/FM/CS/IA/IF) 2
- Table of contents 3
- 1.2 Principle of measurement 10
- 1 Introducon 11
- 1.4 Warranty 12
- 1.5 Disposal 12
- 2 Inline refractometer sensor 13
- 2.2 Mounng the sensor 14
- 2.2.2 PR-23 mounng guide 15
- 3 Indicang transmier DTR 17
- 3.3.1 Interconnecng cable 18
- 3.3.2 Connecng sensor 19
- 3.3.6 Reset buon 22
- 4 Prism wash systems 25
- 4.2.2 Prism wash systems 26
- 4.2.3 Prism wash nozzles 33
- 34
- 5.1.1 Inial check 37
- 5.1.2 Calibraon check 38
- 5.1.3 Tesng prism wash 38
- 5.2.1 Keyboard funcons 39
- 5.2.2 Display setup 39
- Figure 5.3 Display setup menu 40
- 5.3 Viewing system informaon 41
- 5.4.1 Opcal image 42
- 5.4.2 Opcal image with IDS 42
- 5.4.3 Diagnosc values 43
- 5.4.4 Temperature measurement 44
- 5.4.5 Sensor head humidity 44
- 6.1.1 Exponenal damping 45
- 6.1.2 Linear damping 46
- 6.1.3 Slew rate limit 46
- 6.2.1 External hold 47
- 6.2.2 Hold during wash 47
- 6.2.3 Tolerance me 47
- 6.2.4 QF threshold 48
- 6.2.5 Hold source interacons 48
- 6.2.6 Hold and signal damping 49
- 6.3 Configuring relays 50
- 6 Configuraon and calibraon 51
- 6.4 Configuring input switches 52
- 6.5.1 Configuring mA outputs 53
- Figure 6.12 The six layers of 56
- 6.6.1 The chemical curve 57
- 6.6.3 Field calibraon 57
- 6.6.5 Direct BIAS adjustment 59
- 6.7.1 Wash cycle 59
- RECOVERY 60
- INTERVAL 60
- PRECOND 60
- Figure 6.15 Wash logic 61
- Figure 6.16 Wash cycle 62
- 7 Regular maintenance 65
- 7.3.2 Replacing the dryer 67
- Figure 7.3 Removal of prism 68
- 8 Troubleshoong 71
- (DTR Main menu > 72
- Display setup > 72
- Contrast&Backlight) 72
- Open Front panel 72
- Remove PR-10500 cover 72
- 8.1.2 Diagnosc LEDs 74
- 8.1.3 Display unreadable 75
- NO SENSOR 76
- NO SIGNAL 76
- SHORT-CIRCUIT 76
- HIGH SENSOR HUMIDITY 77
- HIGH SENSOR TEMP 77
- HIGH TRANSMITTER TEMP 77
- LOW TRANSMITTER VOLT 77
- NORMAL OPERATION 77
- OUTSIDE LIGHT ERROR 78
- NO OPTICAL IMAGE 78
- PRISM COATED 78
- OUTSIDE LIGHT TO PRISM 79
- LOW IMAGE QUALITY 79
- NO SAMPLE 79
- TEMP MEASUREMENT FAULT 79
- 8.3 Wash 80
- 8.4 Diagnosc messages table 81
- 400 1020 83
- 50 60 70 80 83
- 9.3.3 PR-23-AC specificaons 86
- 9.3.4 PR-23-AC parts list 87
- Flow cell type A B C D 89
- SECTION A-A 90
- SCALE 1 : 2 90
- 9.3.6 PR-23-AC I-Line fing 91
- 9.4.1 PR-23-AP model code 92
- 9.4.3 PR-23-AP specificaons 93
- 9.4.4 PR-23-AP parts list 94
- 9.4.6 PR-23-AP I-Line fing 96
- 97
- 9.5.2 PR-23-GC specificaons 99
- 9.5.3 PR-23-GC parts list 100
- 6(&7,21$$ 101
- 9 Sensor specificaons 103
- PR-23 instrucon manual 104
- 9.6.2 PR-23-GP specificaons 107
- 9.6.3 PR-23-GP parts list 108
- 9.8429.842 110
- 250.0250.0 110
- 9.7.2 PR-23-RP specificaons 112
- 9.7.3 PR-23-RP parts list 113
- 9.7.5 PR-23-RP dimensions 115
- PR-23-RP mounng in 2” line 118
- 9.8.2 PR-23-M specificaons 122
- 9.8.3 PR-23-M parts list 123
- 9.8.5 PR-23-MS specificaons 125
- 9.8.6 PR-23-MS parts list 126
- Note! Keep sensor 128
- Cable downwards 128
- Saunders valve body flow cell 129
- PR-23-W Sensor 129
- 9.9.2 PR-23-W specificaons 131
- 9.9.3 PR-23-W parts list 132
- Figure 9.30 PR-23-W mounng 133
- 9.10.1 Equipment 134
- 9.10.2 Installaon 136
- 9.11.1 Equipment 138
- Ignition hazard! 140
- Avoid impact! 140
- SAFE A REAHAZARDOUS A REA 141
- 9.11.3 Isolator/barriers 143
- PROCESS REFRACTOMETER 145
- 10.2.1 Transmier model code 147
- 10.2.2 STR model code 147
- 10.3 Specificaons 148
- 148
- 10.4 Transmier parts list 149
- 11 Safe-Drive™ 151
- 11.2 Specificaons 152
- 11.3.1 PR-23-SD sensor 153
- 11.3.3 Safe-Drive™ Retractor 155
- Side view 156
- Top view 156
- 11.4.2 Wiring 160
- : Drain valves 162
- 11.5.1 Sensor inseron 164
- 11.5.2 Sensor removal 167
- 11.6.1 Wash nozzle inseron 170
- 11.6.2 Wash nozzle removal 171
- Cross-over 173
- Straight-through 173
- 12.2.1 IP sengs for DTR 175
- Figure 12.8 Ping OK 177
- Request med out 177
- 12.4 Instrument homepage 178
- 12.4.1 Remote panel 179
- 12.5.1 Communicaon protocol 180
- Response format 181
- Request and response errors 181
- Measurement results 183
- DTR status 183
- 13 Sensor verificaon 185
- 13.1 Refracve index n 186
- 13.2 Verificaon procedure 186
- 13.4 Correcve acon 190
- − 191
- A Glossary and abbreviaons 197
- DTR DISPLAY VALUES 207
- Sample no LAB% CALC T n 207
- E DTR command selecon tree 209
- PROCESS INSTRUMENTS 213
Related products and manuals for Equipment K-patents PR-23
Equipment K-patents SeedMaster 2 User Manual
(105 pages)
(105 pages)
Equipment K-patents PR-33-AC User Manual
(54 pages)
(54 pages)
Equipment K-patents PR-33-AC User Manual
(53 pages)
(53 pages)
Equipment K-patents mA-Output User Manual
(20 pages)
(20 pages)
Equipment K-patents PR-33-AC User Manual
(56 pages)
(56 pages)
Equipment K-patents PR-33-S User Manual
(44 pages)
(44 pages)
Equipment K-patents PR-33-S User Manual
(43 pages)
(43 pages)
Equipment K-patents FC-11 User Manual
(24 pages)
(24 pages)
Equipment K-patents DD-01 User Manual
(37 pages)
(37 pages)
Equipment K-patents PR-01-S User Manual
(107 pages)
(107 pages)
Equipment K-patents PR-03 User Manual
(123 pages)
(123 pages)
© 2020, manymanuals.com. All rights reserved. | 0.948 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals